Application of wear-resistant coating by electrospark alloying method using an eutectic electrode material
Електронний науковий архів Науково-технічної бібліотеки Національного університету "Львівська політехніка"
Переглянути архів Інформація| Поле | Співвідношення | |
| Title |
Application of wear-resistant coating by electrospark alloying method using an eutectic electrode material
|
|
| Creator |
Bilous, Oleksiy
Mahura, Bohdan |
|
| Contributor |
Lviv Polytechnic National University
|
|
| Subject |
electro-spark alloying
eutectic alloy fractography of a break X-ray phase method spectral analysis sintering method |
|
| Description |
Analysis of the literature database connected with the usage of an electro-spark alloying (ESA) for tool hardening has been carried out in the article. Necessity of developing a new tungstenless electrode materials with eutectic structure for improvement of an electro-spark alloying technologies has been proved. Therefore, the structure of a new eutectic Fe-Mn-C-B-Si-Cr-Li alloy system has been developed and manufacturing techniques of an alloying by a sintering method has been offered. The article presents the scientific data obtained on the modern equipment. Electronic spectroscopy – spectral analysis of an eutectic electrode alloy has been carried out by an electronic spectrometer of JAMP-10S model (JEOL). X-ray phase analysis of the alloy has been carried out on the “Dron-UM1”. |
|
| Date |
2019-02-11T13:44:18Z
2019-02-11T13:44:18Z 2018-01-29 2018-01-29 |
|
| Type |
Article
|
|
| Identifier |
Bilous O. Application of wear-resistant coating by electrospark alloying method using an eutectic electrode material / Oleksiy Bilous, Bohdan Mahura // Ukrainian Journal of Mechanical Engineering and Materials Science. — Lviv : Lviv Politechnic Publishing House, 2018. — Vol 4. — No 1. — P. 40–48.
http://ena.lp.edu.ua:8080/handle/ntb/44124 Bilous O. Application of wear-resistant coating by electrospark alloying method using an eutectic electrode material / Oleksiy Bilous, Bohdan Mahura // Ukrainian Journal of Mechanical Engineering and Materials Science. — Lviv : Lviv Politechnic Publishing House, 2018. — Vol 4. — No 1. — P. 40–48. |
|
| Language |
en
|
|
| Relation |
Ukrainian Journal of Mechanical Engineering and Materials Science, 1 (4), 2018
[1] A. D. Verkhoturov, et al., “Svoistva iznoso-stoikikh pokrytii iz evtekticheskikh splavov khrom – karbid” [“Properties of wear-resistant coatings from eutectic chromium-carbide alloys”], Poroshkovaia metallurgiia [Powder metallurgy], no. 3, pp. 45–50, 1984. [in Russian]. [2] O. V. Bilous, et al., “Vprovadzhennia suchasnykh tekhnolohii zmitsnennia instrumentalnykh stalei dlia obrobky derevynnykh materialiv” [“Implementation of modern technologies for the strengthening of instrumental steels for the processing of wood materials”], Naukovyi visnyk NLTU Ukrainy [Scientific Bulletin of UNFU], vol. 22.6, pp. 86–90, 2012. [in Ukrainian]. [3] V. M. Golubetc, and M. I. Pashechko, “Printcipy sozdaniia i osobennosti formirovaniia evtekticheskikh pokrytii iz zhidkoi fazy” [“Principles of creation and features of the formation of eutectic coatings from the liquid phase”], Fizyko-khimichna mekhanika materialiv [Physico-Chemical Mechanics of Materials], no, pp. 25–29, 1984. [in Russian]. [4] V. M. Golubetc, Dolgovechnost evtekticheskikh pokrytii v korrozionnykh sredakh [Durability of eutectic coatings in corrosive environments]. Kyiv, Ukraine: Naukova Dumka Publ., 1990. [in Russian]. [5] V. P. Glukhov, Boridnye pokrytiia na zheleze i stali [Boride coatings on iron and steel]. Kyiv, Ukraine: Naukova Dumka Publ., 1970. [in Russian]. [6] M. I. Pashechko, V. M. Golubetc, and M. V. Chernetc, Formirovanie i friktcionnaia stoikost evtekticheskikh pokrytii [Formation and frictional resistance of eutectic coatings]. Kyiv, Ukraine: Naukova Dumka Publ., 1993. [in Russian]. [7] M. I. Pashechko, and V. M. Golubetc, “Sposob polucheniia evtekticheskikh termo-diffuzionnonaplavlennykh pokrytii” [“Method for obtaining eutectic thermo-diffusion-deposited coatings”], Metallovedenie i termicheskaia obrabotka metallov [Metallurgy and heat treatment of metals], no. 6, pp. 26–30, 1989. [in Russian]. [8] V. M. Golubetc, and M. I. Pashechko, Iznosostoikost pokrytii iz evtektiki na osnove sistemy Fe-Mn-C-B [Wear resistance of eutectic coatings based on the Fe-Mn-C-B system]. Kyiv, Ukraine: Naukova Dumka Publ., 1989. [in Russian]. [9] M. V. Maltcev, Metallografiia tugoplavkikh, redkikh i radioaktivnykh metallov i splavov [Metallography of refractory, rare and radioactive metals and alloys]. Moscow, Russia: Metallurgiia Publ., 1971. [in Russian]. [10] V. M. Holubets, and O. V. Bilous, “Trybotekhnichni vlastyvosti zmitsnenykh elektroiskrovoiu i lazernoiu obrobkoiu instrumentalnykh stalei pry tochinni derevynnykh materialiv” [“Tribotechnical properties of hardened electroscope and laser treatment of instrumental steels when finishing wood materials”], Naukovyi visnyk [Scientific Bulletin], vol. 12.2, pp. 107–116, 2002. [in Ukrainian]. [11] V. K. Grishin, et al., Svoistva litiia [Properties of lithium]. Moscow, Russia: Metallurgizdat Publ., 1963. [in Russian]. [12] M. Khansen, and K. Anderko, Struktury dvoinykh splavov [Structures of binary alloys], vol. 2. Moscow, Russia: Metallurgizdat Publ., 1962. [in Russian]. [13] R. P. Elliot, Struktury dvoinykh splavov [Structures of binary alloys]. Moscow, Russia: Metallurgiia Publ., 1970. [in Russian]. [14] O. V. Bilous, et al., “Vplyv vydu nanesenoho pokryttia na trybotekhnichni vlastyvosti rizhuchoho instrumentu” [“Influence of the kind of applied coating on the tribotechnical properties of the cutting tool”], Naukovyi visnyk: Problemy derevoobrobky na rubezhi XXI stolittia: nauka, osvita, tekhnolohii [Scientific Bulletin: Problems of woodworking at the turn of the 21st century: science, education, technologies], vol. 9.5, pp. 239–245, 1999. [in Ukrainian]. [15] O. V. Bilous, et al., “Vplyv rezhymiv rizannia na stiikist instrumentu pry tochinni derevyny” [“Effect of cutting modes on the stability of the tool for finishing wood”], Naukovyi visnyk [Scientific Bulletin], vol. 11.1, pp. 88–89, 2000. [in Ukrainian]. [16] O. B. Hasii, “Rozrobka evtektychnykh elektrodiv dlia elektroiskrovoho zmitsnennia detalei mashyn i osnashchennia” [“Development of eutectic electrodes for electroscrew strengthening of machine parts and equipment”], PhD dissertation, Karpenko Physico-Mechanical institute of the NAS of Ukraine, Lviv, Ukraine, 1993. [in Ukrainian]. [1] A. D. Verkhoturov, et al., "Svoistva iznoso-stoikikh pokrytii iz evtekticheskikh splavov khrom – karbid" ["Properties of wear-resistant coatings from eutectic chromium-carbide alloys"], Poroshkovaia metallurgiia [Powder metallurgy], no. 3, pp. 45–50, 1984. [in Russian]. [2] O. V. Bilous, et al., "Vprovadzhennia suchasnykh tekhnolohii zmitsnennia instrumentalnykh stalei dlia obrobky derevynnykh materialiv" ["Implementation of modern technologies for the strengthening of instrumental steels for the processing of wood materials"], Naukovyi visnyk NLTU Ukrainy [Scientific Bulletin of UNFU], vol. 22.6, pp. 86–90, 2012. [in Ukrainian]. [3] V. M. Golubetc, and M. I. Pashechko, "Printcipy sozdaniia i osobennosti formirovaniia evtekticheskikh pokrytii iz zhidkoi fazy" ["Principles of creation and features of the formation of eutectic coatings from the liquid phase"], Fizyko-khimichna mekhanika materialiv [Physico-Chemical Mechanics of Materials], no, pp. 25–29, 1984. [in Russian]. [4] V. M. Golubetc, Dolgovechnost evtekticheskikh pokrytii v korrozionnykh sredakh [Durability of eutectic coatings in corrosive environments]. Kyiv, Ukraine: Naukova Dumka Publ., 1990. [in Russian]. [5] V. P. Glukhov, Boridnye pokrytiia na zheleze i stali [Boride coatings on iron and steel]. Kyiv, Ukraine: Naukova Dumka Publ., 1970. [in Russian]. [6] M. I. Pashechko, V. M. Golubetc, and M. V. Chernetc, Formirovanie i friktcionnaia stoikost evtekticheskikh pokrytii [Formation and frictional resistance of eutectic coatings]. Kyiv, Ukraine: Naukova Dumka Publ., 1993. [in Russian]. [7] M. I. Pashechko, and V. M. Golubetc, "Sposob polucheniia evtekticheskikh termo-diffuzionnonaplavlennykh pokrytii" ["Method for obtaining eutectic thermo-diffusion-deposited coatings"], Metallovedenie i termicheskaia obrabotka metallov [Metallurgy and heat treatment of metals], no. 6, pp. 26–30, 1989. [in Russian]. [8] V. M. Golubetc, and M. I. Pashechko, Iznosostoikost pokrytii iz evtektiki na osnove sistemy Fe-Mn-C-B [Wear resistance of eutectic coatings based on the Fe-Mn-C-B system]. Kyiv, Ukraine: Naukova Dumka Publ., 1989. [in Russian]. [9] M. V. Maltcev, Metallografiia tugoplavkikh, redkikh i radioaktivnykh metallov i splavov [Metallography of refractory, rare and radioactive metals and alloys]. Moscow, Russia: Metallurgiia Publ., 1971. [in Russian]. [10] V. M. Holubets, and O. V. Bilous, "Trybotekhnichni vlastyvosti zmitsnenykh elektroiskrovoiu i lazernoiu obrobkoiu instrumentalnykh stalei pry tochinni derevynnykh materialiv" ["Tribotechnical properties of hardened electroscope and laser treatment of instrumental steels when finishing wood materials"], Naukovyi visnyk [Scientific Bulletin], vol. 12.2, pp. 107–116, 2002. [in Ukrainian]. [11] V. K. Grishin, et al., Svoistva litiia [Properties of lithium]. Moscow, Russia: Metallurgizdat Publ., 1963. [in Russian]. [12] M. Khansen, and K. Anderko, Struktury dvoinykh splavov [Structures of binary alloys], vol. 2. Moscow, Russia: Metallurgizdat Publ., 1962. [in Russian]. [13] R. P. Elliot, Struktury dvoinykh splavov [Structures of binary alloys]. Moscow, Russia: Metallurgiia Publ., 1970. [in Russian]. [14] O. V. Bilous, et al., "Vplyv vydu nanesenoho pokryttia na trybotekhnichni vlastyvosti rizhuchoho instrumentu" ["Influence of the kind of applied coating on the tribotechnical properties of the cutting tool"], Naukovyi visnyk: Problemy derevoobrobky na rubezhi XXI stolittia: nauka, osvita, tekhnolohii [Scientific Bulletin: Problems of woodworking at the turn of the 21st century: science, education, technologies], vol. 9.5, pp. 239–245, 1999. [in Ukrainian]. [15] O. V. Bilous, et al., "Vplyv rezhymiv rizannia na stiikist instrumentu pry tochinni derevyny" ["Effect of cutting modes on the stability of the tool for finishing wood"], Naukovyi visnyk [Scientific Bulletin], vol. 11.1, pp. 88–89, 2000. [in Ukrainian]. [16] O. B. Hasii, "Rozrobka evtektychnykh elektrodiv dlia elektroiskrovoho zmitsnennia detalei mashyn i osnashchennia" ["Development of eutectic electrodes for electroscrew strengthening of machine parts and equipment"], PhD dissertation, Karpenko Physico-Mechanical institute of the NAS of Ukraine, Lviv, Ukraine, 1993. [in Ukrainian]. |
|
| Rights |
© Національний університет „Львівська політехніка“, 2018
© Bilous O., Mahura B., 2018 |
|
| Format |
40-48
9 application/pdf image/png |
|
| Coverage |
Lviv
|
|
| Publisher |
Lviv Politechnic Publishing House
|
|